electronic PCB
Budget / Salary$30–250
TypeFreelance project
LocationRemote
Posted32 minutes ago
Project Description, PIR to SAMD21 to LED COB
A schematic was designed to turn on a 12 volt COB strip
(BTF-LIGHTING UL Listed FCOB COB LED Strip Light Warm White 3000K
DC12V) with a PIR (AM312). When the PIR motion detector is
triggered a signal is sent to a microprocessor, SEEED SAMD21,
which is programmed to stay on for five minutes.
Closet_SEED_XIAO_schematic_240920.jpg
A PCB was designed from the schematic.
closet_xiao_PCB_top_layer_b_&_w_240930.jpg
In testing the system works in turning on the LED strip.
But in turning off the light it has three behaviors.
1. Sometimes, but rarely, the system operates as designed.
That is, the light comes on when the PIR is triggered,
stays on for five minutes and then goes off.
2. More often, the light comes on when triggered
and after five minutes the light goes off for
a split second and comes back on.
3. In other tests the system comes on and never goes
off.
The PIR has been tested and operates normally. The
tests demonstrate that the PIR, when triggered
sends a 3.2 volt signal for 3 seconds and then
returns to 0 volts.
A test at pin 3 of the SAMD21 shows that the
output of the microprocessor is the same as the
the three behaviors of the LEDs described above.
A test at the Gate of the transistor is also the same as the
the three behaviors of the LEDs described above.
The project has three parts:
1. Either rework the existing schematic or draft
a new schematic that will operate the LED strip
as intended and described in the first two
sentences of this text.
2. After the schematic by contractor is delivered to
Allen Pitts, Allen Pitts will design a PCB in
software DipTrace based on the schematic by contractor.
A JPG of the PCB, similar
to the JPG marked 'Closet XIAO 240930',
will be delivered to the contractor The second part
of project is for the contractor to review the
PCB and advise Allen Pitts that the PCB
design is consistent with the schematic
by contractor. If the PCB
design is not consistent with the schematic
by contractor, the contractor will
make recommendations for rework of
the PCB by Allen Pitts and the reworked
PCB will be delivered to the contractor
for review and advice.
3. When the PCB is received by Allen Pitts
from the manufacturer the PCB will be tested by
Allen Pitts and the result of the tests
will be presented to the contractor.
The project is split into three parts
because after the schematic by contractor
is received by Allen Pitts it will take
some days to translate the schematic
by contractor into a PCB. And after
the PCB is reviewed and approved
it can take weeks for the PCB to
be delivered by the manufacturer.
Because of this project timeline
there will be four payments:
1. Project acceptance and initiation.
2. Schematic by contractor delivered.
3. PCB reviewed and approved.
4. PCB tested for normal operation.
Although the microprocessor sketch is
not an item in the project the sketch is attached
herewith to provide context.
A schematic was designed to turn on a 12 volt COB strip
(BTF-LIGHTING UL Listed FCOB COB LED Strip Light Warm White 3000K
DC12V) with a PIR (AM312). When the PIR motion detector is
triggered a signal is sent to a microprocessor, SEEED SAMD21,
which is programmed to stay on for five minutes.
Closet_SEED_XIAO_schematic_240920.jpg
A PCB was designed from the schematic.
closet_xiao_PCB_top_layer_b_&_w_240930.jpg
In testing the system works in turning on the LED strip.
But in turning off the light it has three behaviors.
1. Sometimes, but rarely, the system operates as designed.
That is, the light comes on when the PIR is triggered,
stays on for five minutes and then goes off.
2. More often, the light comes on when triggered
and after five minutes the light goes off for
a split second and comes back on.
3. In other tests the system comes on and never goes
off.
The PIR has been tested and operates normally. The
tests demonstrate that the PIR, when triggered
sends a 3.2 volt signal for 3 seconds and then
returns to 0 volts.
A test at pin 3 of the SAMD21 shows that the
output of the microprocessor is the same as the
the three behaviors of the LEDs described above.
A test at the Gate of the transistor is also the same as the
the three behaviors of the LEDs described above.
The project has three parts:
1. Either rework the existing schematic or draft
a new schematic that will operate the LED strip
as intended and described in the first two
sentences of this text.
2. After the schematic by contractor is delivered to
Allen Pitts, Allen Pitts will design a PCB in
software DipTrace based on the schematic by contractor.
A JPG of the PCB, similar
to the JPG marked 'Closet XIAO 240930',
will be delivered to the contractor The second part
of project is for the contractor to review the
PCB and advise Allen Pitts that the PCB
design is consistent with the schematic
by contractor. If the PCB
design is not consistent with the schematic
by contractor, the contractor will
make recommendations for rework of
the PCB by Allen Pitts and the reworked
PCB will be delivered to the contractor
for review and advice.
3. When the PCB is received by Allen Pitts
from the manufacturer the PCB will be tested by
Allen Pitts and the result of the tests
will be presented to the contractor.
The project is split into three parts
because after the schematic by contractor
is received by Allen Pitts it will take
some days to translate the schematic
by contractor into a PCB. And after
the PCB is reviewed and approved
it can take weeks for the PCB to
be delivered by the manufacturer.
Because of this project timeline
there will be four payments:
1. Project acceptance and initiation.
2. Schematic by contractor delivered.
3. PCB reviewed and approved.
4. PCB tested for normal operation.
Although the microprocessor sketch is
not an item in the project the sketch is attached
herewith to provide context.
Apply on Freelancer →
Project sourced from Freelancer.com. Applications happen directly on the original platform — we never collect your data.